Star Fleet Battles: Federation Police Cutter
- Thread starter Sgt_G
- Start date
Great work so far 
Beautiful work. This ship and the original (old) Light Cruiser were the "odd ducks" of the Fed fleet back then.
As far as I'm concerned ship deck plans should be on 11x17 or larger to get the best benefit great work there. 
@Bernard Guignard --- Given that the printable image is 111.5 x 35 scale-meters, what scale would you think it should be published as? (Of course, it's not my call what size paper / scale it will be published; that will be up to ADB if they want to publish it at all.)
At 1:200 scale, that's ~22 x 7 inch. At 1:250 scale, it's 17.6 x 5.6 inch. At 1:275 scale, it does fit on the sheet at ~16x5 inch.
At 1:200 scale, that's ~22 x 7 inch. At 1:250 scale, it's 17.6 x 5.6 inch. At 1:275 scale, it does fit on the sheet at ~16x5 inch.
Depends on the type of border that your putting on the data on and wether you want to put multiple decks on a single sheet or 1 deck per sheet
The Star Stream class booklet of General plans has be done up to be printed on 11x17 sheets. Any thing larger requires
a plotting service or purchasing a plotter.
Architectural C size or Ansi C is a nice as is D size I started out hand drafting on C and D paper
Cygnus.net has my c size work up on his site. My Battleship deck plans (never finished by the way) were done on D size.
https://www.deviantart.com/bernard-...eneral-Plans-Starstream-class-Yacht-610020210
https://www.deviantart.com/bernard-guignard/gallery/66169054/uss-broadsword-project
I hope this helps have a great day
The Star Stream class booklet of General plans has be done up to be printed on 11x17 sheets. Any thing larger requires
a plotting service or purchasing a plotter.
Architectural C size or Ansi C is a nice as is D size I started out hand drafting on C and D paper
Cygnus.net has my c size work up on his site. My Battleship deck plans (never finished by the way) were done on D size.
https://www.deviantart.com/bernard-...eneral-Plans-Starstream-class-Yacht-610020210
https://www.deviantart.com/bernard-guignard/gallery/66169054/uss-broadsword-project
I hope this helps have a great day
Yeah, no, I don't have any kind of border/frame like that. Also, all my labels are inside the area they represent (with a couple just outside along the edge) like this:
I don't have any arrows pointing from a label to the item in question. I found that my program (Floor Plan Plus v2) is not very good on keeping text the same width relative to the drawing when zooming in/out to different scales, so it's next to impossible to judge where the end of the arrow goes next to the text block. Yes, I really should convert the files over to TurboCAD.
BTW, I created that HVAC from scratch, and I must say I'm rather pleased with how it turned out.
I do have a copyright notice along the side (within the width of the printable area) and a title bar like this:
also within the printable width/length. Notice how "Primary Sensor" is off-center? It looks fine whatever scale I print at, but weirdly only on-screen at certain zoom levels. Quite annoying.
In theory, I can print two deck per 17x11 sheet 1:275 or 1:300 scale. I'd just have to calculate the spacing between them.
I don't have any arrows pointing from a label to the item in question. I found that my program (Floor Plan Plus v2) is not very good on keeping text the same width relative to the drawing when zooming in/out to different scales, so it's next to impossible to judge where the end of the arrow goes next to the text block. Yes, I really should convert the files over to TurboCAD.
BTW, I created that HVAC from scratch, and I must say I'm rather pleased with how it turned out.
I do have a copyright notice along the side (within the width of the printable area) and a title bar like this:
also within the printable width/length. Notice how "Primary Sensor" is off-center? It looks fine whatever scale I print at, but weirdly only on-screen at certain zoom levels. Quite annoying.
In theory, I can print two deck per 17x11 sheet 1:275 or 1:300 scale. I'd just have to calculate the spacing between them.
One of the most recent edits that I made was to take two pairs of enlisted (petty officer) "one-plus-one" quarters (separate rooms with a shared lavatory) ....
.... and turned them into two married quarters:
The screen-shots were done at different scales. In reality, they are the same exact overall size.
.... and turned them into two married quarters:
The screen-shots were done at different scales. In reality, they are the same exact overall size.
Last edited:
Similar threads
